Home > Furniture Hardware > Furniture Mechanisms >

RECLINER CHAIR FOOTREST RELEASE LEVER - ROUND SHAPE
Recliner chair footrest release unit with a round black plastic housing
Refer to the measuring guide in the 'Extended Information' tab below
  
Alternative Views:
TRADE PRICES? Login or Contact Us

Scroll to end of page to select and purchase the size you require
Replacement recliner chair lever handle with cable that releases the footrest. The round black plastic housing and cables are available in a range of cable and tail lengths.

Item# Item Name Retail Price Qty Add
ACCRT-C32B RECLINER FOOTREST RELEASE | BLACK PLASTIC | CABLE 960mm | LONG TAIL 115mm
$21.69 ($18.86 exc GST)
Awaiting Stock
ACCRT-C32 RECLINER FOOTREST RELEASE | BROWN PLASTIC | CABLE 960mm | LONG TAIL 115mm
$37.12 ($32.28 exc GST)
Awaiting Stock
ACCRT-C28B RECLINER FOOTREST RELEASE | BLACK PLASTIC | CABLE 730mm | SHORT TAIL 68mm with SPRING
$111.57 ($97.02 exc GST)
ACCRT-C34B RECLINER FOOTREST RELEASE | BLACK PLASTIC | CABLE 870mm | SHORT TAIL 75mm
$37.12 ($32.28 exc GST)
ACCRT-C28 RECLINER FOOTREST RELEASE | BROWN PLASTIC | CABLE 730mm | SHORT TAIL 68mm
$37.12 ($32.28 exc GST)
Awaiting Stock
Check the items you wish to purchase, then click


Features:
  • Cable & Housing sold as a set.




Technical Specs:

  • Although housing dimensions differ slightly, they will still fit neatly into the chair's recess.
  • Don't worry if your measurements are a couple of millimetres different.
  • Ensure you purchase the appropriate 'Tail Length' for your recliner - refer to the Measuring Guide under 'Extended Information'




How To Instructions:


Measuring Guide:

  • (A) Not applicable when purchasing a handle with the cable already fitted.
  • Tail Length (B): Measure in a straight line from the end of the black plastic activator tab to the inside of the 'S' fitting - a difference of a few millimetres will work fine.
  • Cable Length (C): Measure from the round barrel 'T' shape, inside the plastic housing, to the end of the 'S' fitting.
Recliner Chair Footrest Cable & Handle Replacement Instructions:

You Will Need:
  • Drill (a long drill bit works best)
  • Needle-nose pliers
  • 2 screws
Installation Instructions
1. Remove the two screws securing the old handle. One screw is located beneath the handle flange, and the other is on the underside of the handle.
2. Carefully tip the chair onto its back.
3. Release the footrest so it is in the open position.
4. Using the needle-nose pliers, Using needle-nose pliers, unhook the metal Z-fitting from the actuator lever. The old cable and handle can now be pulled out through the side of the chair.
5. Install the new cable by following the same path as the old one.
Insert the new handle into the opening on the side of the recliner and feed the cable down through the side of the chair.
6. Secure the new handle using the two screws.
7. From underneath the chair, press the plastic side-snap retaining clip firmly into position on the recliner frame.
8. Attach the metal Z-fitting to one of the holes in the actuator. Some actuators have multiple holes available. Choosing a hole closer to the pivot point generally requires less handle travel to release the footrest, while a hole further away may require a longer pull. Select the hole that provides your preferred handle sensitivity.
9. Test the handle several times to ensure the cable operates smoothly and the footrest opens and closes correctly before returning the recliner to its normal position.
Trouble Shooting:

Q. Is it possible to shorten the tail end of the cable?

Wrapping the excess tail cable around the actuator is a legitimate way to take up extra cable length provided a few conditions are met:
  • The bend radius isn't too tight. The cable should wrap around a reasonably large radius (typically at least 10–15 mm). Tight bends can fatigue the steel strands and increase friction.
  • The cable doesn't rub on moving parts or sharp edges. Any chafing will eventually wear through the cable.
  • The cable still pulls in a straight line where it exits the housing. The Z-clip should engage the actuator without being pulled sideways.
  • The cable doesn't interfere with the actuator's movement. There needs to be clearance throughout the full range of motion.
Advantages:
  • No need to cut or re-terminate the cable.
  • Uses a standard cable for multiple recliner models.
  • Makes manufacturing and inventory simpler.
Potential disadvantages:
  • Slightly higher friction than a straight cable.
  • If the loop is too small or poorly routed, the cable can fatigue over time.
  • The actuator needs to have enough space or a designed path for the wrap.